Print

Arabian American Center January Training & Development
Program Title:
Electrical Equipment Commissioning &Troubleshooting
Location:
شرم الشيخ
Date:
29.01.2017 - 02.02.2017
Fees:
$ 3000

Description

Course Objective:

     Following the attendance at this course, participants will return to their respective organizations equipped with new or refreshed skills to ensure that electrical equipment and control systems are tested and commissioned in a fashion that ensures reduced costs and or start-up delays plus identified faults or problems are repaired and the underlying causes are identified and eliminated to reduce further failures.
       On successful completion of this seminar, participants will have:
        • A better understanding of commissioning procedures
        • A better understanding of troubleshooting procedures
        • An improved capability in the use of test equipment
        • A better understanding of failure modes and failure analysis
        • A refreshed awareness of electrical safety concerns.

.

Who Should Attend:

     This course is intended for Electrical Engineers, Electrical Supervisors and Electrical Technicians engaged in the commissioning, testing, start-up, troubleshooting, maintenance and repair of Electrical Equipment and Control Systems. Because the methods and examples are generic, personnel from all industries will benefit. Participants need no specific requirements other than good understanding of electricity and magnetism and some relevant experience.

.

Course Contents:

               • The Technology of Electrical Equipment
                                 o Transformers
                                 o Power supplies (UPS)
                                 o Batteries
                                 o Generators
                                 o Switchgear
                                 o Motor control centers (MCC)
                                 o Disconnect switches
                                 o Neutral ground resistors (NGR)
                                 o Variable frequency/speed drives (VFD/VSD)
                                 o Programmable logic controllers (PLC) & distributed control systems (DCS)
                                 o Power monitoring
                                 o Control relays/timers/switches
                                 o Motor/feeder protective devices
                                 o Motors (AC & DC)
                                 o Miscellaneous equipment - heaters, solenoid valves, electric valve

                                     actuators and signaling/alarm devices

                • Commissioning and Testing of Electrical Equipment
                                 o Methods
                                 o Terminology
                                 o Principles
                                 o Special techniques
                                 o NEC check lists

               • Troubleshooting of Electrical Equipment
                                 o Methods
                                 o Terminology
                                 o Principles
                                 o Special techniques
                                 o Case studies/examples
                                 o Single line drawings
                                 o Group exercises

               • The Use of Test Equipment
                                 o Digital voltmeter (DVM)
                                 o Oscilloscopes
                                 o Megger
                                 o Frequency meter
                                 o Temperature probes/pyrometers
                                 o Ammeters
                                 o Power meters
                                 o Load banks
                                 o Digital hydrometers
                                 o Cable fault locators

               •The Interpretation and Use of Drawings
                                 o Single-line electrical drawings
                                 o Control schematics
                                 o Wiring lists
                                 o P&ID’s
                                 o Logic and standard symbols
                                 o The Development of a Job Plan
                                 o Identification of the troubleshooting step-by-step sequence
                                 o Procedure preparation
                                 o Documentation
                                 o Follow-up
                                 o Safety considerations and training

               • The Identification and Repair of Problems/Failures
                                 o Common mode failures
                                 o Phase imbalance
                                 o Contact pitting/arcing
                                 o Electronic component failure
                                 o Fusing
                                 o Motor windings/bearings/brushes
                                 o Ballasts
                                 o Excitation circuits
                                 o Battery cells
                                 o Inverters/rectifiers
                                 o Bushings
                                 o Switches
                                 o Control circuits
                                 o Ground faults

               • A review of Safety Requirements
                                 o Area classifications
                                 o NEC electrical codes
                                 o Safety information

               • Open session: Case Studies, Questions and Answers

30 Sobbhy Fahmey St. - Ard El-Golf - Heliopolis - Cairo - Egypt
Tel: +201001029959/+201066687900/+202 24199019 – Fax: +202 24170419
www.aactd.net E-mail: training@aactd.net
ISO 9001:2008 Certificate No. 01 100 105040 - TUV Rheinland - Germany – WWW.TUV.COM